ขอบคุณครับ
Announcement
Collapse
No announcement yet.
D.I.Y.ตอน ต่อแอมป์ 40+40 w. ราคาไม่ถึงพัน
Collapse
X
-
มาแล้วครับ ชุดใน se-ed เอามา ทำเล่นๆ เสียงดีเหมือนกัน ใช้ อัดกับ ลำโพงคอม (แอมพัง) ก็เสียงรับได้ครับ
ทั้งชุดมี แค่ c ขาออกที่ไม่ได้ใช้ในชุดที่จัดมา .. เดียวขอมีอารมจะbi-cap ได้เรื่องว่าไงเดียวมกล่าวอีกที
ที่ซื้อมาอยากได้แค่ ic น่ะและแถวนี้หาซื้อยาก ไปse-ed เลย จัดมาสักชุด ใครอยากเอาไว้ลองฟีมือ หรือ ต่อฟังเล่นไม่ได้ ซีเรียดความใสของเสียงก็น่าเล่นอยู่ครับ
Comment
-
Originally posted by keang View Postไอซีเบอร์ไรครับ
ฮาดไวร์ซะด้วย ขาอะหลั่ยที่ยาวเกิน ตัดทิ้งบ้างก็ดีครับ
ใช้สายไฟหรือขาอะไหล่ก็ได้ เชื่อมตัวถังวอลลุ่มกับกราวน์ จะช่วยลดปัญหาเสียงฮัมเวลาเอามือไปสัมผัสตัววอลลุ่ม
ขายาวๆ ขี้เกรียจตัดครับ 1เพราะมีลื้อแน่ 2จะได้เอาไปเล่นวงจรอื่นต่อได้ครับ
ส่วนตัวถึงวอลุ่มลง G เนี่ย เห็นมาเยอะ ครับเพิ่งเข้าใจ ว่าทำไหมเดียวไปลองขอบคุณมากครับ
Originally posted by fenderfree View Postเจ๋งแฮะ แบบนี้น่าจะเป็นวงจรแบบ OTL เปลี่ยน C output เหมือนเปลี่ยนลำโพงใหม่เลยลองดูสิ
ic TDA ใช่ป่าวครับ ขั้ว RCA นี่ไปงัดออกมาจากเครื่องเล่น CD ใช่ป่าวว
ขั้ว RAC ก็งัดแงะจาก VCD เก่าๆ จะหมดบ้านแล้วครับ อ้อนพ่อขอศพ TV อยู๋คงมีไรให้เล่นเยอะเดียวได้แล้วจะมาชำแหละหาอะไหล่กันต่อไป.....
เน้นถูกครับ ปล.เงินช๊อตแต่ต้นเดือน 555
Comment
-
Originally posted by pluanantIC TEA2025B ครับ
TEA2025B - STEREO AUDIO AMPLIFIER - STMicroelectronics
datasheet
The TEA2025B/Dis a monolithic integrated circuit in 12+2+2 Powerdip and 12+4+4 SO, intended for use as dual or bridge power audio amplifier portable radio cassette players.
- Dual or Bridge Connection Modes
- Few External Components
- Supply Voltage Down to 3V
- High Channel Separation
- Very Low Switch ON/OFF Noise
- Max Gain of 45dB with Adjust External Resistor
- Soft Clipping
- Thermal Protection
- 3V < VCC < 15V
- P = 2 1W, VCC = 6V, RL = 4W
- P = 2 2.3W, VCC = 9V, RL = 4W
- P = 2 0.1W, VCC = 3V, RL = 4W
Bridge Circuit
Stereo Circuit
Stability
A good layout is recommended in order to avoid oscillations.
Generally the designer must pay attention on the following points:
- Short wires of components and short connections.
- No ground loops.
- Bypass of supply voltage with capacitors as nearest as possible to the supply I.C.pin. The low value(poliester)capacitors must have good temperature and frequency characteristics.
- No sockets.
Heatsink
The heatsink can have a smaller factor of safety compared with that of a conventional circuit. There is no device damage in the case of excessive junction temperature: all that happens is that PO (and therefore Ptot) and Id are reduced.Last edited by keang; 19 Oct 2010, 14:46:58.
Comment
-
Originally posted by keang View Postโดนตัวไหนครับ ท่าทางจะสนุกกัน
ถ่ายไว้หมดแล้วครับ...เดี๋ยวอัพให้ดูครับ
Originally posted by pluanant View Postพี่เสือครับ แอมกระป๋องพี่เท่าไรอ่ะ? อยาก ซิววว
----
ตอนนี้กำลัง ดูใจว่าจะไปเยี่ยงไรต่อ ก่ะ bi cap ทั้งแผงและ
แงะic ขาเือบหัก ใจหายวาบบบบ
Comment
Comment